MXnet MV41V2 API V1.00 ~ 07-22-2025

Table of API Commands

MV-41 Main Board API Commands

Command	Description
H	Help
STA	Show Global System Status
SET RST	Reset to Factory Default
SET RBT	System Reboot
SET ADDR xx	Set System Address to xx (xx=00-99 where 00=Single)
SET LCD ON Tx	Set how long LCD remains on (x=0-3 where 0=Always, 1=15s, 2=30s, 3=60s)
SET KEY LOCK ON/OFF	ON - Buttons on AC-MXNET-1G-MV41V2 are locked OFF - Buttons on AC-MXNET-1G-MV41V2 are unlocked
GET ADDR	Get System Address
GET STA	Get System Status
GET LCD ON T	Get on time for LCD
GET KEY LOCK	Get Key Lock Status
SET OUTx MV LAYOUTy	Set Output x to Multiview Layout y x=0-1 where 0=all y=0-20 where: 0 = PIP OFF 1 = 2x2 PIP 2 = 1/3(bottom) 3 = 3+1(left) 4 = cascade 5-20 = User Defined Mode (Default 2x2 PIP)
SET MV LAYOUTx INy VC zz	Set Multiview Layout x Input y Video Coordinate zz x=0-20 where: 0 = PIP OFF 1 = 2x2 PIP 2 = 1/3(bottom) 3 = 3+1(left) 4 = cascade 5-20 = User Defined Mode (Default 2x2 PIP) y=1-4 (Inputs 1-4) zz=INPUT_WIDTH.INPUT_HEIGHT.INPUT_X.INPUT_Y.TILE_WIDTH.TILE_HEIGHT.TILE_X.TILE_Y Input parameters affect image cropping - INPUT_WIDTH = width of image - INPUT_HEIGHT = height of image - INPUT_X = x coordinate to start image cropping - INPUT_Y = y coordinate to start image cropping Tile parameters affect display output - TILE_WIDTH = width of displayed image - TILE_HEIGHT = height of displayed image - TILE_X = x position of tile in multiview - TILE_Y = y position of tile in multiview
SET MV PRIORITY x1.x2.x3.x4	Set Multiview Tile Priority tile_1_priority.tile_2_priority.tile_3_priority.tile_4_priority t1=1-4 t2=1-4 t3=1-4 t4=1-4 1=Highest Priority 4=Lowest Priority
SET OUTx ASPRy	Set Output x Video Aspect Ratio Mode y **Does not apply to PIP mode x=0-1 where 0=all y=0-5 where: 0 = OFF 1 = 4:3 2 =16:9 3 = 21:9 4 = 1.85:1 5 = 2.35:1
SET ASPRMx VCDVy	Set Video Aspect Ratio Mode x Vertical Captor Deletes the Black Edge Value y x=4-5 where: 4 = 1.85/1 5 = 2.35/1 y=0-800 (Video vertical value of the black edge to be)
GET OUTx MV LAYOUT	Get Output x to Multiview Layout Status x=0-1 where 0=all
GET MV LAYOUTx INy VC	Get Multiview Layout x Input y View Coordinate Value Status x=1-20 where: 0 = PIP OFF 1 = 2x2 PIP 2 = 1/3(bottom) 3 = 3+1(left) 4 = cascade 5-20 = User Defined Mode (Default 2x2 PIP) y=0-4 where 0=ALL
GET MV PRIORITY	Get Multiview Tile Priority Status
GET OUTx ASPR	Get Output x Video Aspect Ratio Mode Status x=0-1 where 0=all
GET ASPRMx VCDV	Get Video Aspect Ratio Mode x Vertical Captor Deletes The Black Edge Value x=4-5 where: 4 = 1.85/1 5 = 2.35/1
SET AUD MODEx	Set Multiview Audio Mode x ** If using VIDEO PIP Mode, MVAUD MODE Automatically follows MVAUD IN x=0-1 0 = Follow HDMI Out 1 = Follow MVAUD IN
SET MVAUD INx	Set Multiview Audio Select Input x **PIP MODE ON or AUD MODE 1 Takes Effect Automatically x=1-4 1 = AC-MXNET-1G-DV2 HDMI 1 2 = AC-MXNET-1G-DV2 HDMI 2 3 = AC-MXNET-1G-DV2 HDMI 3 4 = AC-MXNET-1G-DV2 HDMI 4
GET AUD MODE	Get Multiview Audio Mode Status
GET MVAUD IN	Get Multiview Audio Select Input Status
SET OUTx VS INy	Set Output x To Input y x=0-1 where 0=ALL y=1-4 (Input 1-4)
GET OUTx VS	Get Output x Video Route x=0-1 where 0=ALL
SET RIP xxx.xxx.xxx.xxx	Set Route or Gateway IP Address to xxx.xxx.xxx.xxx
SET HIP xxx.xxx.xxx.xxx	Set Host IP Address to xxx.xxx.xxx.xxx
SET NMK xxx.xxx.xxx.xxx	Set Net Mask to xxx.xxx.xxx.xxx
SET TIP zzzz	Set TCP/IP Port to zzzz zzzz=1-9999
SET DHCP y	Set DHCP y y=0-1 where 0=Disable and 1=Enable
GET RIP	Get Route or Gateway IP Address
GET HIP	Get Host IP Address
GET NMK	Get Net Mask
GET TIP	Get TCP/IP Port
GET DHCP	Get DHCP Status
GET MAC	Get MAC Address
SET INx DEMAC zz.zz.zz.zz.zz.zz	Set Input x Decoder MAC Address to zz.zz.zz.zz.zz.zz x=1-4 (Input 1-4)
SET OUTx ENMAC zz.zz.zz.zz.zz.zz	Set Output x Encoder MAC Address to zz.zz.zz.zz.zz.zz x=1 (Output 1)
GET INx DEMAC	Get Input x Decoder MAC Address status x=1-4 (Input 1-4)
GET OUTx ENMAC	Get Output x Encoder MAC Address status x=1 (Output 1)

MXnet 1G CBOX API

Command	Description
config get mv41list	Returns a list of AC-MXNET-1G-MV41V2s in the MXnet 1G ecosystem along with their associated decoders and encoder
config set mv41 add {mv41_ip}	Adds an AC-MXNET-1G-MV41V2 to the mv41list mv41_ip = HIP found on the front panel OLED screen under the NETWORK page
config set mv41 rm {mv41_ip}	Removes an AC-MXNET-1G-MV41V2 from the mv41list mv41_ip = HIP found on the front panel OLED screen under the NETWORK page
config set mv41 connect {mv41_ip}	Creates a TCP connection to the AC-MXNET-1G-MV41V2 on the first available TCP port starting on port 50000 mv41_ip = HIP found on the front panel OLED screen under the NETWORK page
config set MV-41 close {mv41_ip}	Closes the TCP connection between the CBOX and the AC-MXNET-1G-MV41V2 mv41_ip = HIP found on the front panel OLED screen under the NETWORK page
config set mv41 vas {tx_mac} {rx_mac[:rx_mac:rx_mac:rx_mac...]} {mv41_ip}	Routes the AC-MXNET-1G-MV41V2 encoder output to any desired MXnet V2 decoder in the system tx_mac=MAC Address of the AC-MXNET-1G-MV41V2’s encoder rx_mac=MAC Address of the MXnet V2 decoder(s) mv41_ip = HIP found on the front panel OLED screen under the NETWORK page
config set MV-41 port {new_port} {mv41_ip}	Manually assign a TCP forwarding port for the connection between the CBOX and the AC-MXNET-1G-MV41V2 new_port=49152-65535 TCP forwarding port between CBOX and AC-MXNET-1G-MV41V2 mv41_ip = HIP found on the front panel OLED screen under the NETWORK page

MV-41 Main Board API Commands

SET API Commands

SET RST

Description:

Reset the MV-41 main board to factory defaults. This will change the MV-41 main board HIP address to 192.168.1.239 with a /24 subnet.

Example command and feedback response:


SET RST
RST

SET RBT

Description:

Reboot the MV-41 main board

Example command and feedback response:


SET RBT
RBT

SET ADDR xx

Description:

Set System Address to xx

xx = 00-99
- 00 = Single

Example command and feedback response:


SET ADDR 00
ADDR 00

SET LCD ON Tx

Description:

Set System Address to xx

x = 0-3
- 0 = Always on
- 1 = 15s
- 2 = 30s
- 3 = 60s

Example command and feedback response:


SET LCD ON T0
LCD ON T0

SET KEY LOCK ON/OFF

Description:

Sets the lock condition of the buttons on the front panel of the AC-MXNET-1G-MV41V2

ON = Buttons on AC-MXNET-1G-MV41V2 are locked
OFF = Buttons on AC-MXNET-1G-MV41V2 are unlocked

Example command and feedback response:


SET KEY LOCK OFF
KEY LOCK OFF

SET OUTx MV LAYOUTy

Description:

Changes the layout of the multiview for the designated output. In the case of the MV-41 main board, there is one output so this will set the layout for the output of the AC-MXNET-1G-MV41V2

x = 0-1
- 0 = All outputs
- 1 = OUT1
y = 0-20 where:
- 0 = PIP OFF
- 1 = 2x2 PIP
- 2 = 1/3(bottom)
- 3 = 3+1(left)
- 4 = cascade
- 5-20 = User Defined Mode (Default 2x2 PIP)

Example command and feedback response:


SET OUT0 MV LAYOUT1
OUT0 MV LAYOUT 1

SET MV LAYOUTx INy VC zz

Description:

This command will not activate the layout of a multiview, but will modify the layout of the multiview for the designated output. In the case of the MV-41 main board, there is one output so this will set the layout for the output of the AC-MXNET-1G-MV41V2.

x = 0-20 where:
- 0 = PIP OFF
- 1 = 2x2 PIP
- 2 = 1/3(bottom)
- 3 = 3+1(left)
- 4 = cascade
- 5-20 = User Defined Mode (Default 2x2 PIP)
y = 1-4 (Inputs 1-4)
zz = INPUT_WIDTH.INPUT_HEIGHT.INPUT_X.INPUT_Y.TILE_WIDTH.TILE_HEIGHT.TILE_X.TILE_Y
- Input parameters affect image cropping
  - INPUT_WIDTH = width of image
  - INPUT_HEIGHT = height of image
  - INPUT_X = x coordinate to start image cropping
  - INPUT_Y = y coordinate to start image cropping
- Tile parameters affect display output
  - TILE_WIDTH = width of displayed image
  - TILE_HEIGHT = height of displayed image
  - TILE_X = x position of tile in multiview
  - TILE_Y = y position of tile in multiview

Example command and feedback response:


SET MV LAYOUT5 IN1 VC 0.0.0.0.1920.1080.0.0
MV LAYOUT5 IN4 VC 0.0.0.0.1920.1080.1920.0

SET MV LAYOUT5 IN2 VC 0.0.0.0.1920.1080.0.1080
MV LAYOUT5 IN2 VC 0.0.0.0.1920.1080.0.1080

SET MV LAYOUT5 IN3 VC 0.0.0.0.1920.1080.960.1080
MV LAYOUT5 IN3 VC 0.0.0.0.1920.1080.960.1080

SET MV LAYOUT5 IN4 VC 0.0.0.0.1920.1080.1920.0
MV LAYOUT5 IN4 VC 0.0.0.0.1920.1080.1920.0

SET MV PRIORITY t1.t2.t3.t4

Description:

Changes the tile priority within the layout of the multiview. This will control the tile layering designation which tile is on the top layer (layer 1), the next layer (layer 2), the second lowest layer (layer 3), and the bottom layer (layer 4).

t1=1-4 (Tile 1)
t2=1-4 (Tile 2)
t3=1-4 (Tile 3)
t4=1-4 (Tile 4)
- 1=Highest Priority
- 4=Lowest Priority

Example command and feedback response:


SET MV PRIORITY 1.2.3.4
MV PRIORITY 1.2.3.4

SET OUTx ASPRy

Description:

Sets the state of aspect ratio control and the mode for the image output.

Note: Does not apply to multiview mode - OUTx MV LAYOUT0 required

x = 0-1
- 0 = All outputs
- 1 = OUT1
y = 0-5 where:
- 0 = OFF
- 1 = 4:3
- 2 =16:9
- 3 = 21:9
- 4 = 1.85:1
- 5 = 2.35:1

Example command and feedback response:


SET OUT0 ASPR1
OUT0 ASPR1

SET ASPRMx VCDVy

Description:

Controls the 1.85:1 (4) or 2.35:1 (5) aspect ratios letterboxing pillars by stretching the image vertically to remove them.

x = 4-5
- 4 = 1.85:1
- 5 = 2.35:1
y = 0-800
- Adjusts vertical stretch to remove the letterboxing bars

Example command and feedback response:


SET ASPRM5 VCDV400
ASPRM5 VCDV400

SET AUD MODEx

Description:

Configure the audio mode for the MV-41 main board. If set to Follow HDMI Out and input tile 1, 2, 3, or 4 are selected, the audio will follow the single source video selected. If set to Follow MVAUD IN, the input tile selection does not affect the audio output.

Note: If in multiview mode, MVAUD automatically follows MVAUD IN

x = 0-1
- 0 = Follow HDMI Out
- 1 = Follow MVAUD IN

Example command and feedback response:


SET AUD MODE0
AUD MODE 0

SET MVAUD INx

Description:

Selects the the audio tile input for MVAUD IN.

x = 1-4
- 1 = Tile input 1
- 2 = Tile input 2
- 3 = Tile input 3
- 4 = Tile input 4

Example command and feedback response:


SET MVAUD IN3
MVAUD IN 3

SET OUTx VS INy

Description:

Disables multiview mode and enables single source mode on the MV-41 main board and selects a specific tile input to display.

x = 0-1
- 0 = All outputs
- 1 = OUT1
y = 1-4
- 1 = Tile input 1
- 2 = Tile input 2
- 3 = Tile input 3
- 4 = Tile input 4

Example command and feedback response:


SET OUT0 VS IN1
OUT0 VS IN1
OUT1 MV LAYOUT 0

SET RIP xxx.xxx.xxx.xxx

Description:

Set the Route or Gateway IP address of the MV-41 main board.

xxx.xxx.xxx.xxx = Any valid IP address (1.1.1.1 - 255.255.255.255)

Example command and feedback response:


SET RIP 169.254.1.1
RIP 169.254.001.001

SET HIP xxx.xxx.xxx.xxx

Description:

Set the Host IP address of the MV-41 main board.

xxx.xxx.xxx.xxx = Any valid IP address (1.1.1.1 - 255.255.255.255)

Example command and feedback response:


SET HIP 169.254.1.20
HIP 169.254.001.020

SET NMK xxx.xxx.xxx.xxx

Description:

Set the Subnet Mask of the MV-41 main board.

xxx.xxx.xxx.xxx = Any valid IP address (1.1.1.1 - 255.255.255.255)

Example command and feedback response:


SET NMK 255.255.0.0
NMK 255.255.000.000

SET INx DEMAC zz.zz.zz.zz.zz.zz

Description:

Configures the MAC address of the AC-MXNET-1G-DV2 connected to the user specified tile input.

x = 1-4
- 1 = Tile input 1’s AC-MXNET-1G-DV2
- 2 = Tile input 2’s AC-MXNET-1G-DV2
- 3 = Tile input 3’s AC-MXNET-1G-DV2
- 4 = Tile input 4’s AC-MXNET-1G-DV2
zz.zz.zz.zz.zz.zz = Any valid MAC Address

Example command and feedback response:


SET IN1 DEMAC 18.8a.6a.02.c0.ef
IN1 DEMAC 18.8a.6a.02.c0.ef

SET OUTx ENMAC zz.zz.zz.zz.zz.zz

Description:

Configures the MAC address of the AC-MXNET-1G-EV2 connected to the MV-41 main board output.

x = 1
- 1 = OUT1’s AC-MXNET-1G-EV2
zz.zz.zz.zz.zz.zz = Any valid MAC Address

Example command and feedback response:


SET OUT1 ENMAC 18.8a.6a.02.c0.f3
OUT1 ENMAC 18.8a.6a.02.c0.f3

GET API Commands

GET STA

Description:

Pulls a general overview status of pertinent settings on the MV-41 main board.

Example command and feedback response:


GET STA
ADDR 00
LCD ON T0
KEY LOCK OFF
FAN SPEED 2
OUT1 VS IN1
OUT1 MV LAYOUT 2
MV LAYOUT1 IN1 VC 0.0.0.0.1920.1080.0.0
MV LAYOUT1 IN2 VC 0.0.0.0.1920.1080.1920.0
MV LAYOUT1 IN3 VC 0.0.0.0.1920.1080.0.1080
MV LAYOUT1 IN4 VC 0.0.0.0.1920.1080.1920.1080
MV LAYOUT2 IN1 VC 0.0.0.0.2560.1440.660.0
MV LAYOUT2 IN2 VC 0.0.0.0.1280.720.0.1440
MV LAYOUT2 IN3 VC 0.0.0.0.1280.720.1280.1440
MV LAYOUT2 IN4 VC 0.0.0.0.1280.720.2560.1440
MV LAYOUT3 IN1 VC 0.0.0.0.2560.2160.1280.0
MV LAYOUT3 IN2 VC 0.0.0.0.1280.720.0.0
MV LAYOUT3 IN3 VC 0.0.0.0.1280.720.0.720
MV LAYOUT3 IN4 VC 0.0.0.0.1280.720.0.1440
MV LAYOUT4 IN1 VC 0.0.0.0.3840.2160.0.0
MV LAYOUT4 IN2 VC 0.0.0.0.960.540.1440.810
MV LAYOUT4 IN3 VC 0.0.0.0.960.540.1920.1080
MV LAYOUT4 IN4 VC 0.0.0.0.960.540.2400.1350
MV PRIORITY 4.3.2.1
ASPRM4 VCDV0
ASPRM5 VCDV0
OUT1 ASPR0
RIP 169.254.001.001
HIP 169.254.001.020
NMK 255.255.000.000
TIP 23
DHCP 0
MAC 18.8a.6a.02.c0.f4
IN1 DEMAC 18.8a.6a.02.c0.ef
IN2 DEMAC 18.8a.6a.02.c0.f0
IN3 DEMAC 18.8a.6a.02.c0.f1
IN4 DEMAC 18.8a.6a.02.c0.f2
OUT1 ENMAC 18.8a.6a.02.c0.f3

GET ADDR

Description:

Retrieves MV-41 system address.

xx = 00-99
- 00 = Single

Example command and feedback response:


GET ADDR
ADDR 00

GET LCD ON T

Description:

Retrieves the LCD on time.

x = 0-3
- 0 = Always on
- 1 = 15s
- 2 = 30s
- 3 = 60s

Example command and feedback response:


GET LCD ON T
LCD ON T0

GET KEY LOCK

Description:

Pulls the current lock condition of the buttons on the front panel of the AC-MXNET-1G-MV41V2

ON = Buttons on AC-MXNET-1G-MV41V2 are locked
OFF = Buttons on AC-MXNET-1G-MV41V2 are unlocked

Example command and feedback response:


GET KEY LOCK
KEY LOCK OFF

GET OUTx MV LAYOUT

Description:

Verifies the layout of the multiview for the designated output. In the case of the MV-41 main board, there is one output so this will pull the layout for the output of the AC-MXNET-1G-MV41V2

x = 0-1
- 0 = All outputs
- 1 = OUT1

Example command and feedback response:


GET OUT0 MV LAYOUT
OUT1 MV LAYOUT 0

GET MV LAYOUTx INy VC

Description:

This command will retrieve the video coordinate information for a specified layout’s tile input.

x = 0-20 where:
- 0 = PIP OFF
- 1 = 2x2 PIP
- 2 = 1/3(bottom)
- 3 = 3+1(left)
- 4 = cascade
- 5-20 = User Defined Mode (Default 2x2 PIP)
y = 1-4 (Inputs 1-4)

Example command and feedback response:


GET MV LAYOUT1 IN1 VC
MV LAYOUT1 IN1 VC 0.0.0.0.1920.1080.0.0

GET MV LAYOUT1 IN2 VC
MV LAYOUT1 IN2 VC 0.0.0.0.1920.1080.1920.0

GET MV LAYOUT1 IN3 VC
MV LAYOUT1 IN3 VC 0.0.0.0.1920.1080.0.1080

GET MV LAYOUT1 IN4 VC
MV LAYOUT1 IN4 VC 0.0.0.0.1920.1080.1920.1080

GET MV PRIORITY

Description:

Finds the tile priority within the layout of the multiview so the user may know the layering designation of tiles. Top layer (layer 1), the next layer (layer 2), the second lowest layer (layer 3), and the bottom layer (layer 4).

Example command and feedback response:


GET MV PRIORITY
MV PRIORITY 1.2.3.4

GET OUTx ASPR

Description:

Determines the state of aspect ratio control and the mode for the image output.

x = 0-1
- 0 = All outputs
- 1 = OUT1

Example command and feedback response:


GET OUT0 ASPR
OUT1 ASPR0

GET ASPRMx VCDV

Description:

Displays the vertical stretch parameter for the 1.85:1 (4) or 2.35:1 (5) aspect ratios letterboxing pillars.

x = 4-5
- 4 = 1.85:1
- 5 = 2.35:1

Example command and feedback response:


GET ASPRM4 VCDV
ASPRM4 VCDV0

GET AUD MODE

Description:

Returns the current audio mode for the MV-41 main board. If set to 0 then the MV-41 main board is set to Follow HDMI Out. The the audio will follow the single source video selected. If set to 1 then the MV-41 main board is set to Follow MVAUD IN. The input tile selection does not affect the audio output.

Example command and feedback response:


GET AUD MODE
AUD MODE 0

GET MVAUD IN

Description:

Shows the current tile input selected audio for MVAUD IN.

Example command and feedback response:


GET MVAUD IN
MVAUD IN 1

GET OUTx VS

Description:

Shows which tile input source is currently selected. 0 means no tile input sources is selected as the current output. If a tile input source is selected, the command will return IN1-4

Example command and feedback response:


GET OUT0 VS
OUT1 VS 0

GET OUT0 VS
OUT1 VS IN1

GET RIP xxx.xxx.xxx.xxx

Description:

Returns the Route or Gateway IP address of the MV-41 main board.

Example command and feedback response:


GET RIP
RIP 169.254.001.001

GET HIP xxx.xxx.xxx.xxx

Description:

Returns the Host IP address of the MV-41 main board.

Example command and feedback response:


GET HIP
HIP 169.254.001.020

GET NMK xxx.xxx.xxx.xxx

Description:

Returns the Subnet Mask of the MV-41 main board.

Example command and feedback response:


GET NMK
NMK 255.255.000.000

GET INx DEMAC

Description:

Pulls the MAC address of the AC-MXNET-1G-DV2 connected to the user specified tile input.

x = 1-4
- 1 = Tile input 1’s AC-MXNET-1G-DV2
- 2 = Tile input 2’s AC-MXNET-1G-DV2
- 3 = Tile input 3’s AC-MXNET-1G-DV2
- 4 = Tile input 4’s AC-MXNET-1G-DV2

Example command and feedback response:


GET IN1 DEMAC
IN1 DEMAC 18.8a.6a.02.c0.ef

GET OUTx ENMAC zz.zz.zz.zz.zz.zz

Description:

Pulls the MAC address of the AC-MXNET-1G-EV2 connected to the MV-41 main board output.

x = 1
- 1 = OUT1’s AC-MXNET-1G-EV2

Example command and feedback response:


GET OUT1 ENMAC
OUT1 ENMAC 18.8a.6a.02.c0.f3

Misc. API Commands

H

Description:

The help command will show an organized/formatted table of all SET/GET for the MV-41 main board.

Example command and feedback response:


H
=======================================================================================================================================
=************************************************************Systems HELP*************************************************************=
=-------------------------------------------------------------------------------------------------------------------------------------=
=                        System Address = 00           F/W Version : 0.02                                                             =
=   Azz                                :  All Commands start by Prefix System Address zz, if [01-99]                                  =
=-------------------------------------------------------------------------------------------------------------------------------------=
=   H                                  : Help                                                                                         =
=   STA                                : Show Global System Status                                                                    =
=   SET RST                            : Reset to Factory Defaults                                                                    =
=   SET RBT                            : System Reset to Reboot                                                                       =
=   SET ADDR xx                        : Set System Address to xx {xx=[00~99](00=Single)}                                             =
=   SET LCD ON Tx                      : Set LCD Remain On Time{x=[0~3](0=Always ON,1=15,2=30,3=60Sec)}                               =
=   SET KEY LOCK ON/OFF                : Set Key Lock On/Off                                                                          =
=   GET ADDR                           : Get System Address                                                                           =
=   GET STA                            : Get System System Status                                                                     =
=   GET LCD ON T                       : Get LCD Remain On Time                                                                       =
=   GET KEY LOCK                       : Get Key Lock Status                                                                          =
=-------------------------------------------------------------------------------------------------------------------------------------=
=Audio/Video Settings Commands: (Note:output number(x)=HDMI,x=[1])                                                                    =
=   SET OUTx MV LAYOUTy                : Set Output x to Multiview Layout y                                                           =
=                                        {x=[0~1](0=ALL), y=[0-20](0=PIP OFF,1=2x2 PIP,2=1/3(bottom),3=3+1(left),                     =
=                                        4=cascade,5-20=User Defined Mode(Default show 2x2 PIP))}                                     =
=   SET MV LAYOUTx INy VC zz           : Set Multiview Layout x Input y View Coordinate Value zz{zz=w1.h1.x1.y1.w2.h2.x2.y2,          =
=                                        w1.h1.x1.y1=Input Captor Cut Param,w2.h2.x2.y2=Output Captor Display Param                   =
=                                        x=[1~20],y=[1-4],w1/w2=[0-3840],h1/h2=[0-2160],x1/x2=[0-3840],y1/y2=[0-2160]}                =
=   SET MV PRIORITY x1.x2.x3.x4        : Set Multiview Priority Path x1.x2.x3.x4{x1.x2.x3.x4=[1-4]                                    =
=                                        Note:NUM 1 indicates the highest priority}                                                   =
=   SET OUTx ASPRy                     : Set Output x Video Aspect Ratio Mode y(Does Not Apply to Video PIP Mode)                     =
=                                        {x=[0~1](0=ALL), y=[0-5](0=OFF,1=4/3,2=16/9,3=21/9,4=1.85/1,5=2.35/1)}                       =
=   SET ASPRMx VCDVy                   : Set Video Aspect Ratio Mode x Vertical Captor Deletes The Black Edge Value y                 =
=                                        {x=[4-5](4=1.85/1,5=2.35/1), y=[0-800]Video Vertical value of the black edge to be deleted}  =
=   GET OUTx MV LAYOUT                 : Get Output x to Multiview Layout Status{x=[0~1](0=ALL)}                                      =
=   GET MV LAYOUTx INy VC              : Get Multiview Layout x Input y View Coordinate Value Status{x=[1~20],y=[0-4](0=All)}         =
=   GET MV PRIORITY                    : Get Multiview Priority Path Status                                                           =
=   GET OUTx ASPR                      : Get Output x  VIDEO Aspect Ratio Mode Status{x=[0~1](0=ALL)}                                 =
=   GET ASPRMx VCDV                    : Get Video Aspect Ratio Mode x Vertical Captor Deletes The Black Edge Value{x=[4-5]}          =
=-------------------------------------------------------------------------------------------------------------------------------------=
=Multiview Audio Settings Commands:                                                                                                   =
=   SET AUD MODEx                      : Set Multiview Audio Mode x{x=[0-1](0-Follow HDMI Out,1-Follow MVAUD IN)}                     =
=                                        Note:If Use VIDEO PIP Mode,MVAUD MODE Automatically Follow MVAUD IN!                         =
=   SET MVAUD INx                      : Set Multiview Audio Select Input x{x=[1-4](1-4=HDMI1-4 AUDIO IN)}                            =
=                                        NOTE:PIP MODE ON or AUD MODE 1 Takes Effect Automatically                                    =
=   GET AUD MODE                       : Get Multiview Audio Mode Status                                                              =
=   GET MVAUD IN                       : Get Multiview Audio Select Input Status                                                      =
=-------------------------------------------------------------------------------------------------------------------------------------=
=Output Setup Commands: (Note:output number(x)=HDMI,x=[1])                                                                            =
=   SET OUTx VS INy                    : Set Output x To Input y{x=[0~1](0=ALL), y=[1~4]}                                             =
=   GET OUTx VS                        : Get Output x Video Route{x=[0~1](0=ALL)}                                                     =
=-------------------------------------------------------------------------------------------------------------------------------------=
=Network Setup Command: ( xxx=[000-255], zzzz=[0001~9999]                                                                             =
=   SET RIP xxx.xxx.xxx.xxx            : Set Route IP Address to xxx.xxx.xxx.xxx                                                      =
=   SET HIP xxx.xxx.xxx.xxx            : Set Host IP Address to xxx.xxx.xxx.xxx                                                       =
=   SET NMK xxx.xxx.xxx.xxx            : Set Net Mask to xxx.xxx.xxx.xxx                                                              =
=   SET TIP zzzz                       : Set TCP/IP Port to zzzz                                                                      =
=   SET DHCP y                         : Set DHCP {y=[0~1](0=Dis,1=Enable)}                                                           =
=   GET RIP                            : Get Route IP Address                                                                         =
=   GET HIP                            : Get Host IP Address                                                                          =
=   GET NMK                            : Get Net Mask                                                                                 =
=   GET TIP                            : Get TCP/IP Port                                                                              =
=   GET DHCP                           : Get DHCP Status                                                                              =
=   GET MAC                            : Get MAC Address                                                                              =
=-------------------------------------------------------------------------------------------------------------------------------------=
=IP Decoder/Encoder MAC Command: (zz=[000-255]                                                                                        =
=   SET INx DEMAC zz.zz.zz.zz.zz.zz    : Set Input x Decoder MAC Address to zz.zz.zz.zz.zz.zz{x=[1-4]}                                =
=   SET OUTx ENMAC zz.zz.zz.zz.zz.zz   : Set Output x Encoder MAC Address to zz.zz.zz.zz.zz.zz{x=[1]}                                 =
=   GET INx DEMAC                      : Get Input x Decoder MAC Address status{x=[1-4]}                                              =
=   GET OUTx ENMAC                     : Get Output x Encoder MAC Address status{x=[1]}                                               =
=-------------------------------------------------------------------------------------------------------------------------------------=
=*************************************************************************************************************************************=
=======================================================================================================================================

STA

Description:

The status command will show an organized/formatted table of the MV-41 main board’s pertinent information and statuses.

Example command and feedback response:


STA
STA
=======================================================================================================================================
=***********************************************************Systems STATUS************************************************************=
=-------------------------------------------------------------------------------------------------------------------------------------=
=                        System Address = 00           F/W Version : 0.02                                                             =
=-------------------------------------------------------------------------------------------------------------------------------------=
= System Setup Status :                                                                                                               =
=-------------------------------------------------------------------------------------------------------------------------------------=
= RS232 : Baud Rate=57600bps, Data=8bit, Parity=None, Stop=1bit                                                                       =
= LCD Remain ON: Alway                                                                                                                =
= KEY LOCK: OFF                                                                                                                       =
=-------------------------------------------------------------------------------------------------------------------------------------=
= Network Setup(Telnet Server) Status:                                                                                                =
= MAC Address = 18:8a:6a:02:c0:f4                                                                                                     =
= Host IP Address = 169.254.001.020                                                                                                   =
= Net Mask = 255.255.000.000                                                                                                          =
= Router IP Address = 169.254.001.001                                                                                                 =
= TCP Port = 0023                                                                                                                     =
= DHCP = DISABLE                                                                                                                      =
=-------------------------------------------------------------------------------------------------------------------------------------=
= Input Setup Status :                                                                                                                =
= IN1 : EDID = 1080P_2CH            , Link = ON  , HDCP = HDCP2.2 ,                                                                   =
= IN2 : EDID = 1080P_2CH            , Link = ON  , HDCP = HDCP2.2 ,                                                                   =
= IN3 : EDID = 1080P_2CH            , Link = ON  , HDCP = HDCP2.2 ,                                                                   =
= IN4 : EDID = 1080P_2CH            , Link = ON  , HDCP = HDCP2.2 ,                                                                   =
=-------------------------------------------------------------------------------------------------------------------------------------=
= Output Setup Status:                                                                                                                =
= Output1  : Input =  1, Link = ON , Out Stream = ON                                                                                  =
=                                                                                                                                     =
=-------------------------------------------------------------------------------------------------------------------------------------=
=*************************************************************************************************************************************=
=======================================================================================================================================

CBOX API Commands

SET API Commands

config set mv41 add {mv41_ip}

Description:

Adds an AC-MXNET-1G-MV41V2 to the mv41list that the CBOX is tracking.

mv41_ip = HIP found on the front panel OLED screen under the NETWORK page

Example command and feedback response:


config set mv41 add 169.254.1.239
{"cmd":"config set mv41 add 169.254.1.239","info":"Add success","code":0}

config set mv41 rm {mv41_ip}

Description:

Removes an AC-MXNET-1G-MV41V2 from the mv41list

mv41_ip = HIP found on the front panel OLED screen under the NETWORK page

Example command and feedback response:


config set mv41 rm 169.254.1.239
{"cmd":"config set mv41 rm 169.254.1.239","info":"Delete success","code":0}

config set mv41 connect {mv41_ip}

Description:

Creates a TCP connection to the AC-MXNET-1G-MV41V2 on the first available TCP port starting on port 50000.

mv41_ip = HIP found on the front panel OLED screen under the NETWORK page

Example command and feedback response:


config set mv41 connect 169.254.1.239
{"code":0,"cmd":"config set mv41 connect 169.254.1.239"}

config set mv41 close {mv41_ip}

Description:

Closes the TCP connection between the CBOX and the AC-MXNET-1G-MV41V2

mv41_ip = HIP found on the front panel OLED screen under the NETWORK page

Example command and feedback response:


config set mv41 close 169.254.1.239
{"cmd":"config set mv41 close 169.254.1.239","info":"Close 169.254.1.239 success","code":0}

config set mv41 vas {tx_mac} {rx_mac[:rx_mac:rx_mac:rx_mac...]} {mv41_ip}

Description:

Routes the AC-MXNET-1G-MV41V2 encoder output to any desired MXnet V2 decoder in the system.

tx_mac=MAC Address or Custom Name of the AC-MXNET-1G-MV41V2’s encoder
rx_mac=MAC Address or Custom Name of the MXnet V2 decoder(s)
mv41_ip = HIP found on the front panel OLED screen under the NETWORK page

Example command and feedback response:


config set mv41 vas 188A6A032AD9 RIGHT-V2 169.254.1.239
{"code":0,"cmd":"config set mv41 vas 188A6A032AD9 RIGHT-V2 169.254.1.239"}

config set mv41 port {new_port} {mv41_ip}

Description:

Manually assign a TCP forwarding port for the connection between the CBOX and the AC-MXNET-1G-MV41V2.

new_port=49152-65535
mv41_ip = HIP found on the front panel OLED screen under the NETWORK page

Example command and feedback response:


config set mv41 port 50002 169.254.1.239
{"code":0,"cmd":"config set mv41 port 50002 169.254.1.239"}

GET API Commands

config get mv41list

Description:

Returns a list of AC-MXNET-1G-MV41V2s in the MXnet 1G ecosystem along with their associated decoders and encoder and pertinent information.

Example command and feedback response:


config get mv41list
{"cmd":"config get mv41list","info":{"169.254.1.239":{"rx2_tx":"188A6A01D1DD","rx3":"188A6A032AD7","rx4":"188A6A032AD8","online":true,"tx1_rx":"RIGHT-V2",
"rx3_tx":"188A6A024F24","connect":1,"rx4_tx":"188A6A0157BD","port_link":true,"ip":"169.254.1.239","rx1_tx":"188A6A01D37F","rx1":"188A6A032AD5","rx2":
"188A6A032AD6","tx1":"188A6A032AD9","port":50002},"169.254.1.20":{"rx2_tx":"188A6A01D1DD","tx1_rx":"188A6A0241C6:188A6A0249C4","tx1":"188A6A02C0F3",
"rx4_tx":"188A6A01D37F","rx4":"188A6A02C0F2","rx3_tx":"188A6A024F24","connect":1,"rx3":"188A6A02C0F1","port_link":true,"ip":"169.254.1.20","online":true,
"rx1":"188A6A02C0EF","rx1_tx":"188A6A0157BD","rx2":"188A6A02C0F0","port":50000}},"code":0}

Related Articles
MXNet 10G - API ~ V1.05
The PDF file attached to this article contains available API commands for the MXNet 10G ecosystem. You can connect to the AC-MXNET-10G-CBOX using PuTTY (Connection Method: Telnet, use TCP Port 24) to execute the commands listed in the API ...
MXnet 1G API ~ V1.26.1
Kevin Wang, Director of Product Management, goes through using the MXNET API to control and configure the MXNet CBOX Direct. Current API Version: V1.26.1 Control Box Version: 2.71 && V4.21 and above Instructions and API attached
AC-MXNET-USP-CBOX ~ API V1.07 ~ 02-09-2026
The latest AC-MXNET-USP-CBOX API document can be downloaded here: AC-MXNET-USP-CBOX API The PDF attached in the link above contains the available API commands for the MXNet USP ecosystem. You can connect to the AC-MXNET-USP-CBOX's API server using ...
AC-MXNET-CBOX ~ V2.73 ~ 03/14/2025
NOTICE: If your CBOX is reading firmware as a version of V4.XX, please navigate to this page here: https://support.avproedge.com/portal/en/kb/articles/ac-mxnet-cbox-b-firmware Note: Please update the CBOX first, before attempting updates on the ...
Dante Controller CBOX API ~ V1.00
AC-MXNET-DANTE-CBOX API Published Version: V1.00 Date Published: 6/27/2025 Download Link: https://avproglobal.egnyte.com/dl/wgfnjhLP7P Requirements Dante CBOX RJ-45 cabling Personal Computer Terminal Client capable of establishing telnet/TCP sockets ...