T1-B+ Firmware

T1-B+ Firmware

VERIFYING THAT YOU NEED THE UPGRADE
If you already have version 1.14 or newer you should not upgrade your
firmware to this version. Use the "Get Firmware Version" command from
the Communications menu in Integration Designer to determine the
current firmware version. If the reported version number is 1.14.039
or higher, you do not need this update.

INTEGRATION DESIGNER SUPPORT
You must use Integration Designer 9.0 or higher to perform this update.

FIRMWARE UPGRADE PROCEDURE
1. Choose the "Update Firmware" command on the Communications menu in
   Integration Designer.
2. Select the T1BPLUSFW_114.RFW file included with this README file.
3. Make sure you have your program saved (see the WARNING above), then
   click OK.
4. Plug the USB cable into the T1-B+ and wait for the firmware transfer
   to complete.
5. Unplug the USB cable when prompted, wait for the T1-B+ to reset (this
   should take ten to twenty seconds).
6. Re-connect the USB cable and use the "Get Firmware Version" command
   on the Communications menu to verify that the update completed.  If
   the update was successful, it should report version 1.14.039 as the
   version number.

LIST OF CHANGES IN THIS RELEASE (RELEASE 1.14)
1. Fix for skipping of command trigger codes sent to processor
2. Fix for ZigBee sustain running on too long
3. Reduced sleep current (which means improved battery life)


ARCHIVE

LIST OF CHANGES IN RELEASE 1.12
1. Fix for source LEDs locking up
2. Fix for accelerometer (tilt switch) only working once
3. Reduded accelerometer power consumption during sleep

LIST OF CHANGES IN RELEASE 1.11
1. Fix for incorrect carrier frequency in IR trigger codes
2. Fix for IR trigger codes in standalone macros

LIST OF CHANGES IN RELEASE 1.10
1. Added Companion (SURFiR) Mode
2. Fix for IR codes in macros that have no sustain
3. Added support for disabling tilt switch
4. Improved accelerometer (tilt switch) performance
5. Fix for continuous reboot when battery is critically low
6. Now honoring sustain flag with IR codes for standalone IR

LIST OF CHANGES IN RELEASE 1.02
1. Fix for supporting Creston, AMX and URC RF trigger codes

LIST OF CHANGES IN RELEASE 1.01
1. Fix for system macros called from macros on a standalone button

LIST OF CHANGES IN RELEASE 1.0
1. Initial production release

    • Related Articles

    • T-B+ Specification

      Dual RF transmission capability (433MHz and 2.4GHz with Zigbee® technology). Ergonomic design for effortless, one-handed operation. Tilt switch for automatic backlight activation. Eight source and four general-purpose programmable keypad buttons with ...

    • T1-B+ Operation Guide

      Key Features: Fully customizable and programmable universal controller. Combines multiple factory remote controls into one ergonomic interface. Dual RF capability: 433MHz and 2.4GHz (Zigbee® technology). Eight source and four general-purpose ...

    • IST-5 Specification

      Key Features 5” capacitive-touch screen with 854x480 resolution and ultra-thin bezel. Near-flush mount design, only 0.47”/12mm off the wall. Supports Ethernet and Wi-Fi for control communication. Power options include PoE or 12V DC. High-resolution ...

    • IST-10 Specification

      Touchpanel Features 10” capacitive-touch screen with 1920x1200 resolution and true-black display filter. Near-flush mount design at 0.47”/12mm off the wall. Built-in 10/100 Base-T Ethernet with PoE for seamless control and programming. Supports H.264 ...

    • CX7 Firmware

      VERIFYING THAT YOU NEED THE UPGRADE If you already have version 22.3.31 or newer you should not upgrade your firmware to this version. Use the "Get Firmware Version" command from the Communications menu in TheaterTouch Designer or Integration ...